Premium Products for Security & Automation

ProductsContactSupportWhere to buyEventsM1 TrainingProduct FeedbackSearch

Magic Module Downloads

 
Magic Module Programming and Auxiliary Software
  ELK Application Writer / Code Editor for programming of ELK Magic Modules.
Revision 5.1.17 for 16 KByte Magic Modules.  Includes Magic Control Screen Program
filename: setupext.exe, 3/29/2001, self-extracting, 6.9MB, for Windows 9x, NT, 2000.
Programming Instruction Manual in Acrobat Reader .PDF format.(3 MB)
Magic Module Timer Program is a general purpose multiple day timer. Control lighting, doors, etc via relays or X-10 modules using a Magic Module. The MagicTimer has four(4) independent, 24 hour, 7 day timers. Any 15 minute time block can be turned on or off throughout the day. Any of the four output relays may be turned on or off from each timer. Each timer may send a X-10 On/Off/Dim signal to control lights & other devices.
filename: MagicTimerSetup.exe  5.4MB. Includes the Magic Module Timer Source file in MS Visual Basic 6 format; a good programming example of PC communications with the ELK-MM443 Magic Module.
Magic Module Control from your Casio Cassiopeia Palm PDA.
MagicController for the Cassiopeia, Beta Version 0.1, 3/8/00, filename: MagicController.zip 
Magic Module Data Bus Protocol Document
filename: mmprotocol.exe   4.8MB
  Obsolete - ELK Application Writer / Code Editor for older 4KByte Magic Modules - Software Revision 4.1.0
Includes Magic Control Screen Program
filename: setupext410.exe, 2/29/00, self-extracting, 4.4MB, for Windows 9x, NT.
Obsolete - ELK Code Writer for older 256 byte Magic Modules, Software Revision 1.5.2
filename: setup256.exe, self-extracting, 4.6MB, for Windows 9x, NT

ELK-MV480 Factory Default Messages 
These are the individual words & phrases pre-programmed into each MV480 at the factory.
The phases can be sequentially played together into sentences, i.e. "Front-Door-Is-Open". These files are in the Windows .WAV format. Use the Magic Module Programming Software and the ELK-129 to restore these into the MV480 if needed.

Download (8.4 MB self-extracting(.exe) file) all factory default messages including the .VCM file. After downloading, run "ELK-MV480 Default Messages.exe", then click "Unzip" to extract the WAV files into your "C:\Program Files\MagicModuleExt\WavFiles\" folder. A new folder named "MV480" will be created during the unzipping process.

 These WAV files can also be found on the ELK Development Software CDROM under the " ..\ELK\WavFiles\MV480" folder.
 

   
ELK-MV120 Factory Default Messages (To Support ELK-MV120, no longer produced)
These are the individual words & phrases pre-programmed into each MV120 at the factory.
The phases can be sequentially played together into sentences, i.e. "Front-Door-Is-Open". These files are in the Windows .WAV format and are formatted (scripted) for the ELK-129. Use the Magic Module Programming Software and the ELK-129 to restore these into the MV120 if needed.

Click to listen; right-click to download; or Download (1.7MB self-extracting(.exe) file) all 32 factory default messages including the .VCM file. After downloading, run "ELK-MV120 Default Messages.exe", then click "Unzip" to extract the WAV files into your "C:\Program Files\MagicModuleExt\WavFiles\" folder. A new folder named "MV120_scripted" will be created during the unzipping process.

These WAV files can also be found on the ELK Development Software CDROM under the "..\ELK\WavFiles\MV120_scripted" folder.

Channel Factory Default Message
1. Alarm
2. Activated
3. System is Armed
4. Not Secure
5. Exit Expires in 10 Seconds
6. Please Enter Your Code to Disarm
7. Then Call the Monitoring Station 
8. Exit Immediately
9. AC Power Loss
10. Energy Saving Features
11. Main Entry
12. Hallway
13. Living Room
14. Family Room
15. Dining Room
16. Kitchen
17. Master Bedroom
18. Bedroom 2
19. Bedroom 3
20. Bedroom 4
21. Upstairs
22. Downstairs
23. Basement
24. Garage
25. Door
26. Window
27. Front
28. Back
29. Side
30. Sliding
31. Motion Detector
32. Glass Break Detector
 
Disclaimer: ELK Products, Inc makes no warranties or representations about the accuracy or completeness of these programs. Reasonable steps have been taken to ensure the accuracy of the information contained in these programs, but they could include inaccuracies or typographical errors. By your use of these programs you agree that ELK Products shall not be liable for any such inaccuracies or errors. ELK Products may make improvements and/or changes in these programs at any time. Neither ELK Products nor any of its affiliates shall be liable for any direct, incidental, consequential, indirect or punitive damages arising out of the use of any content from these programs.

 
[ Home ]
ELK Products, Inc. P.O. Box 100, Hildebran, N.C. 28637 USA (828) 397-4200
Copyright � 2010   All rights reserved   Terms and Conditions