Magic Module™
Programmable
Controller
4 Inputs, 4 Outputs,
X-10®, iButton™
|
|
| ELK-MM443
|
| The Magic Module™
(ELK-MM443) is a
four analog or digital input, four relay output programmable
logic controller (PLC). It
may be used as a stand alone field programmable controller in a
vast array of applications from timers, door controllers, simple
process controllers, multiple zone security controls, etc. or as
a networked controller with up to 31 other modules connected on
a common RS-485 data bus. The Magic Module™ supports transmitting and receiving commands
from two way X-10®
Power Line Carrier Devices. Also optional interfaces
are available for reading Temperature,
Clock/Calendar, Wiegand
Proximity devices, Dallas iButton™ identification devices. |
|
The Magic Module™ is programmed by a
personal
computer. The program is stored into re-programmable Electrically
Erasable Programmable Read Only Memory (EEProm memory). The
ELK-MB485 is the interface used to
transfer the program from the computer the Magic Module™.
Also
available.. ELK-MM220, a lower cost 2
digital input, 2 relay output programmable controller.
|
| FEATURES: |
• Four
analog or digital inputs
• Four relay outputs (2 relay outputs may be jumper programmed
for transistor open collector outputs)
• 16,384 program bytes using SIMPLE programming language
• 4 general purpose Counters, range 0 to 255 counts
• 4 general purpose Timers, range 1/10 second to over 255
hours
• Networked to optional PC and up to 31 ELK-MM443’s
through a RS-485 data bus.
• X-10® Power Line Carrier Interface. PL513, PSC04 (Transmit
Only), or TW523, PSC05 (Two Way).
• Analog transmission MM443 to MM443 and Preset Dim
Commands.
• Dallas iButton™ TouchKey Reader with optional
ELK-MA100 or ELK-MA290 interface
• Programs the ELK-MM220 (two inputs, two relay outputs)
• Emulates ELK-MM220 for code development
• Program stored in non-volatile EEProm memory
• Mounts to single or double gang electrical box.
• Optional DIN Rail Mounting. PCB mounts into 4 inch SnapTrack.
• Lifetime Limited Warranty. |
| SPECIFICATIONS: |
•
Inputs:
• Outputs:
• Operating Voltage:
• Current Draw:
• X-10® Interface:
• Data Bus:
• Enclosure: |
4
Analog, 0 to 13.6 volts, with jumper programmable 2k pull up
resistor to 12 V, or 2k pull down resistor to ground. May be
left floating. Software programmable high and low threshold
levels per input for end-of-line resistor circuits. Input
impedance (floating input) - 100K ohms
4 Form "C" Relays, 10 Amps @ 120VAC or 7 Amps @ 28VDC; Two relay outputs may be
configured as open collector transistor outputs - 100 ma. Max.
9.5-15 Volts DC
10 ma. Nominal, 130 ma. Maximum with all relays active.
PL513, PSC04 or TW523, PSC05 - 4
wire RJ-11 telephone style
RS-485, max bus length: 4000 feet w/22 AWG wire
White Plastic: 6.5" W x 4.375"H x 2"D
|
View the ELK-MM443
Data Sheet in Adobe Acrobat
format (right-click to save document to your hard drive)
View the
ELK-MM443
Instruction Manual in Adobe Acrobat
format (right-click to save document to your hard drive)
Magic Module is a trademark of ELK Products, Inc.
X10 is a trademark of X-10 USA.
iButton is a trademark of Dallas Semiconductor |
To order the
ELK-MM443
Call your nearest distributor or ELK
at 1-800-797-9355 for more information
|
|
|
