ELK M1XEP Keypad/Keystroke process to add wireless smoke detector

[Jason Roberts]

What is the keypad/button presses to add a wireless smoke detector?

M1XEP – M1XRF2Hv2 – M1XP keypad

[Brad Weeks]

Are you able to connect to the system using the ElkRP2 software? If so you can learn in a wireless device from ElkRp2 if you have the Honeywell serial number. From keypad programming:

• Press the ELK key, screen should display 1-View/Control Automation Fncts
• Press the 9 key, screen should display 9-Installation Programming (0)
• Press the right arrow key and you should be prompted “Auth Required Enter Valid PIN — This is the Installer Level Keypad Programming Code
• Screen should display 01-Bus Module Enrollment
• Type 14, screen should display 14-Wireless Setup
• Press the right arrow key, screen should display 1: Rec Sel {Up/Down symbols} Prg {right arrow symbol} Receiver Options
• Type 3 and screen should display 3: Learn Sel {Up/Down symbols} Prg {right arrow symbol} Wireless Transmtr
• Press the Right Arrow key
• Type in the 3 digit zone number for the zone you want to learn in and press the right arrow key
• Screen will display WZone = xxx (xxx= the zone number to learn in) TransmitrToLrn
• Press the right arrow key
• Insert the battery into the sensor or trip the tamper switch or move the magnet away from the sensor
• When Learned In you should hear a chime from the keypad and the keypad screen will advance to the next available wireless zone
• Press the ELK Key to save

Additional information can be found starting on page 47 of the M1 Installation Manual and within the M1XRF2Hv2 Installation Manual

[Jason Roberts]

Is the Honeywell serial number in the receiver box or where is it?

I can connect to the M1Xep through ELKrp.

Can you please give the process through ELKrp? I believe through Rp will be easier?

[Brad Weeks]

The Honeywell serial number is a 7 digit number located on the wireless sensor.

Have you enrolled the M1XRF2H?

Have you created a Wireless Group in ElkRP2?

If so:

• Under Zone (Inputs) click on your Wireless Group x
• Click on the zone number you want to configure
• Set the Zone Definition, Type and any other option you need to select
• Click “Wireless Setup”
• Check “Enabled”
• Supervised will either be 0 = Not Supervised for FOBs, 1 = Normal Supervision for Window/Door, 3 = Fire Supervision for Smoke Detectors
• In the H ID box enter the 7 digit serial number for the Honeywell Wireless Sensor
• In most cases the LOOP will equal 1 or reference the Honeywell instructions for the LOOP setting
• Click SAVE and Close the “Change Wireless Zone” window
• From the Zone page click “Send to Control” or “Send and Say”

[Jason Roberts]

Thank you.

• From what I see, the Loop should be 2 for smoke detectors – can you please confirm the loop number again? I will also look at the Honeywell instructions.
• Also, once the H ID is entered, what happens in Tx ID and DL?

[Brad Weeks]

In most cases the LOOP will be 1 for the Honeywell compatible smoke detectors. When you enter the Honeywell serial number in the H ID field the TxID and DL will automatically fill in.

[Jason Roberts]

Should have asked this earlier – once the serial is entered in H ID and saved – at what point is the tab pulled to activate the a batteries? And test?

[Brad Weeks]

After the zone is completely configured Zone Def, Type, Wireless Setup, Enabled Checked, LOOP and H ID entered then remove the battery tab and test

[Jason Roberts]

Thank you. Can you please confirm the settings?

Configuration

• Definition is 10 Fire Alarm
• Type (auto selected) is 5 = Fire/4-Wire Smoke RF
• Atttributes is All Left Unchecked

Wireless Setup

• Enabled is Checked
• Supervised is 3 = Fire Supervision
• H ID entered and Tx ID and Dl auto populated
• Loop is 1

[Author]

Posts